| Adhesives: |
|
EPOXIES: |
| |
|
SIZE / COST |
| |
|
4.5 OZ. |
9
OZ. |
 |
QUIK-CURE 5
Minute epoxy cures to a slightly flexible consistency. This lack of
brittleness allows it to form a lasting bond in areas subjected to high
vibration or stress. Quik-Cure shouldn't be used in areas that are subject
to long term immersion in water; however, it works fine for the internal
structure of wood framed boats. Items bonded with Quik-Cure can be handled
after 15 minutes. |
ADH201 $7.00
BUY |
ADH202 $12.00
BUY |
 |
MID-CURE 15
Minute epoxy is used in areas where more working time is needed. It is
more water resistant and can be used as a substitute for QUIK-CURE in most
applications. Mid-Cure this lines most flexible epoxy. Allow 45 minutes
before handling parts and 2 hours for full strength. |
ADH203 $7.00
BUY |
ADH204 $12.00
BUY |
 |
SLOW-CURE
30 Minute epoxy works best for forming reinforcing fillets on joints. It
has the highest strength of these epoxies. It is waterproof and more heat
resistant. Slow-Cure can be used for bonding if you're willing to wait
overnight. Bonded objects can be handled after 8 hours and the cured epoxy
reaches full strength within 24 hours. |
ADH205 $7.00
BUY |
ADH206 $12.00
BUY |
|
CYANOACRYLATES |
| |
|
SIZE / COST |
| |
|
2
OZ. |
|
 |
INSTA-CURE
Has a water-thin viscosity that wicks deep into joints by capillary action
and cures in a matter of a few seconds. Surfaces to be bonded must be
tight fitting and should be held together while you apply the CA. Thin
CA's work very well on wood since they penetrate into the wood and form
more than just a surface bond. |
ADH103 $8.00 |
BUY |
 |
INSTA-CURE+
is a higher viscosity CA for loose fitting joints in which the adhesive
must bridge gaps. Normally, the thicker CA is applied to one surface and
then the parts are held tightly together for about 5 to 15 seconds. For
large surface areas, including those with close fitting joints such as
laminations, Insta-Cure+ should also be used. |
ADH108
$8.00 |
BUY
|
 |
MAXI-CURE+
extra thick 10-25 second CA is the best CA for most plastics. Maxi-Cure+
bonds hardwood and plywood better than any other hobby adhesive. It can be
carved with a knife or razor blade and sanded to form a finish
indistinguishable from plastic. It's extra thickness makes Maxi-Cure
easier to work with for most applications. |
ADH113 $9.00 |
BUY |
 |
INSTA-FLEX
flexible thin Ca is ideal for many applications, including the
installation of CA hinges. When cured, Insta-Flex does not turn brittle
and remains clear, even if accelerated with Insta-Set. It has superior
shock resistance. Although not as thin in consistency as Insta-Cure,
Insta-Flex still has good penetrating qualities and its application can be
easier to control. |
ADH1191 oz $5.00 |
BUY |
 |
INSTA-SET
is a catalyst which acts as an accelerator that allows CA's to quickly
cure in thick layers by enhancing the alkaline conditions during
polymerization. Insta-Set in a spray bottle is normally used to cure the
CA that flows from joints when parts are pressed together. For difficult
to bond materials, Insta-Set can be applied to one surface and CA to the
opposite surface. When brought together, they will bond instantly.
Insta-Set is formulated with a strawberry scent and activates CA in 6 to 8
seconds without any significant degrading of the CA's strength, which can
occur with many other accelerators. It is compatible with all surfaces,
even clear plastic and white foam. |
ADH151 $4.00 |
BUY |
 |
INSTA-FLEX+
When esthetics are important and a flexible bond is required . When a
joint has a larger than normal gap, flexible CA's provide superior shock
resistent bonds. |
ADH120 1 oz. $5.00 |
BUY
|
 |
UN-CURE Debonder
will soften cured CA. If parts are bonded incorrectly
or your fingers are stuck together, a few drops of UN-CURE will dissolve
the CA in about a minute. Apply on bonded skin and roll apart fingers.
Once stuck, use acetone to clean off softened CA, then wash off with soap
and water. |
ADH161 1
oz. $2.00 |
BUY
|
 |
| |
